ANSI/ASSE Z359.1-2007 个人用防坠落系统,子系统和组件的安全性要求

作者:标准资料网时间:2024-05-02 14:06:27 浏览:8246 来源:标准资料网

【英文标准名称】:SafetyRequirementsforPersonalFallArrestSystems,Subsystems,andComponents
【原文标准名称】:个人用防坠落系统,子系统和组件的安全性要求
【标准号】:ANSI/ASSEZ359.1-2007
【标准状态】:现行
【国别】:美国
【发布日期】:2007
【实施或试行日期】:
【发布单位】:美国国家标准学会(US-ANSI)
【起草单位】:ANSI
【标准类型】:()
【标准水平】:()
【中文主题词】:锚具;组件;防坠落设备;定义;能量吸收器;防跌落系统;防坠落;防护服装;救援腰带;固位带;规范(验收);子系统;测试
【英文主题词】:Anchorages;Components;Crashprotectiondevices;Definitions;Energyabsorbers;Fallarrestsystems;Protectionagainstfall;Protectiveclothing;Rescuebelt;Retentionbelts;Specification(approval);Subsystem;Testing
【摘要】:Thisstandardestablishesrequirementsfortheperformance,design,marking,qualification,instruction,training,inspection,use,maintenanceandremovalfromserviceofconnectors,fullbodyharnesses,lanyards,energyabsorbers,anchorageconnectors,fallarresters,verticallifelines,andself-retractinglanyardscomprisingpersonalfallarrestsystemsforuserswithinthecapacityrangeof130to310pounds(59to140kg).
【中国标准分类号】:P09
【国际标准分类号】:13_340_60
【页数】:
【正文语种】:英语

下载地址: 点击此处下载

返回跳至顶部

上一篇: ANSI/ASSE Z359.3-2007 定位和经过限制系统的安全性要求
下一篇: ANSI/NFPA 77-2007 静电学的推荐实施规程

【英文标准名称】:
【原文标准名称】:C11-104-78的补充1
【标准号】:NFD11-104/A1-1988
【标准状态】:作废
【国别】:法国
【发布日期】:1988-09
【实施或试行日期】:1988-08-05
【发布单位】:法国标准化协会(AFNOR)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:半导体器件;电气耐久试验;耐久试验耐久试验耐久试验;特性;集成电路;符号;测量;电子元部件;电子设备及元件;二极管;定义;电气试验
【英文主题词】:
【摘要】:
【中国标准分类号】:Q81
【国际标准分类号】:
【页数】:3P;A4
【正文语种】:其他

Product Code:SAE J1742
Title:Connections for High Voltage On-Board Road Vehicle Electrical Wiring Harnesses - Test Methods and General Performance Requirements
Issuing Committee:Connector Systems Standards Committee
Scope:SCOPEProcedures included within this specification are intended to cover performance testing at all phases of development,production, and field analysis of electrical terminals, connectors, and components that constitute the electrical connectionsystems in high power (20 V to 600 V and/or >80 A) road vehicle applications. These procedures are applicable only toterminals used for In-Line, Header, and Device Connectors and for cable sizes up to 120 mm2 (4/0).In cases where power levels are mixed in the same connector, (i.e. sensing or normal 14.5 V system circuits with HighPower Contacts) the High Power Contacts must pass SAE J1742 requirements, and all other contacts must pass SAEJ2223-2 requirements. The connection system (housing and high power contacts) shall meet SAE J1742 requirements.The requirements and procedures in this document are not intended for connections internal to electrical/electronicmodules or complete subassemblies.This document does not contain a test for EMI/EMC since these parameters must be tested as a combination of cableand connector. These are considered system level requirements. Determination of the need and type of test must beconsidered at that level.See Appendix C, Design Notes for further information.